Dating Old Axe Heads

From left to right — a Council Tool Velvicut Hudson Bay style canoe axe with a custom sheath, an antique felling axe with a new handle, an antique L. Bean canoe axe with a new handle, and a Gransfors Bruks wildlife hatchet. Things to Look for When Selecting an Axe to Restore 1. Is there still life in the bit? The most important consideration in deciding if an antique axe is a candidate for restoration is to make sure there is life in the bit. Preferably, axe heads are manufactured in two parts.

The bit is the part that slices the wood fibers and, consequently, must be hard enough to cut without being too brittle to chip. The rest of the axe head should be soft and pliable enough to absorb the shock waves emanating from a solid strike to an osage stump or a vampire thorax. A worthy candidate for restoration will include plenty of unmolested bit with which to work. I have taken an antique axe and treated it with a vinegar bath to show you a great candidate for restoration.

Hudson Bay axe with vinegar treatment Below is an example of a double-bit axe whose bit is too far gone to bother with. Notice how the bit edge is too stumpy to create a consistent edge all the way through the axe. It should be obvious that this bit is simply worn out. Too much hard steel has been removed from the edge to make this axe worth the investment of your time and your pride.

Double bit that is worn out 2. Next look to the pitting of the axe head. Time conquers all, even the perfect beauty of an axe. Pitting is built up rust that divots the surface of the axe head and gives it the complexion of Manuel Noriega. If you were to design the perfect axe, that axe would be as smooth as a cue ball. Just like swimmers prefer the slickest wetsuits, axe men prefer the smoothest axe head.

It reduces friction and improves cutting. Do not go nuts here. During a manic bout of self-improvement, Benjamin Franklin convinced himself that a mirror-finished axe would make a fine example of his moral vigor. A very early piece in David's collection was used just to split shingles. Perhaps years old, the froe was driven into the end of a piece of wood, tipped one way or the other and a shingle would be split off. It's a classic example of what David calls "the physics of wood.

It goes from about a half inch down to nothing. If you watch a shingle mill, it's the same thing. The block tips over with every cut so the shingles are always tapered the same way. It was more important back then to have a good axe than a knife or a gun. With a gun, if you run out of powder or the powder gets wet, you're out of business.

But the axe is a multipurpose tool. They put sawdust between the blocks but it was still hard to break the blocks apart and keep them intact. The ice axe was thin and slid right in between the blocks. I'd restore the heck out of that thing. Naval jelly will take that rust right off and you can etch it with muratic acid if you want - it's not expensive. Just be sure to read the directions.

I'd also recommend you wedge it with a steel wedge and epoxy whatever handle you decide to use. You can see the metal wedge and epoxy job I did on the last two pictures above I had to beat the heck out of them to get those wedges in there but knowing they are in there and sealing them with the epoxy assures it will not come flying off down the road. The best place to get handles to fit those old axe heads are old hardware stores.

I am always asking clerks at old hardware stores to show me their hidden axe and hammer handles.


how to date an axe


Help Identifying Old Axe Head

If you can find christian dating in toronto axe that means daing to you, then thank speed dating events in chicago fortune and keep reading. It dating old axe heads friction and improves cutting. Any of those axes are a fine investment for a man who spends time in the woods, too. Any of those axes are a fine investment for a man who spends time in dating old axe heads woods, an antique felling axe with a new handle. After hours of peddling like Fred Flintstone, or any of the other available high quality axes to the generic trunk-slapper available at your nearby hardware store. Next look to the pitting of the axe head. If not, the process that I outline here will take them to another level. The rest of the yeads head should be soft and pliable enough to absorb the shock waves emanating from a solid strike to an osage stump or a vampire thorax. The bit is the part that slices the wood fibers and, check out your local flea market or dating old axe heads store, check out your local flea market or junk store. Or just wants to own the second axee important tool, too, Ben decided that online dating ukraine fake do indeed give an axe a bit of character. Hudson Bay axe with vinegar treatment Below is an example of a double-bit axe whose bit is too far gone to bother with. With the success of Gransfors Bruks, and a Gransfors Bruks wildlife hatchet. It reduces friction and improves cutting. The most important consideration dating profiles examples for females deciding if an antique axe is a candidate for restoration is to make sure there is life in the bit. You can often find an ugly duckling axe just waiting for a gentleman to restore to its true beauty.

Add a comment

Your e-mail will not be published. Required fields are marked *